Note |
---|
For PAM4 interfaces or SyncE Jitter testing, specific modules MUST be used. These modules have been tested by Calnex to ensure they fulfil the requirements for functionality and performance needed to enable correct operation and guarantee the integrity of the timing measurements. Use of other modules may result in a failed test or incorrect result. More information regarding PAM4 transceivers can be found: https://calnexsolutions.atlassian.net/l/cp/dchS6Mxk For SyncE Wander and PTP on non-PAM4 interfaces, most modules should work correctly; known exceptions are detailed below. If you have a module that is not recognised, please let us know. |
Note |
---|
PAM4 100G modules MUST be used with the PAM4 100G interfaces. PAM4 200G modules MUST be used with the PAM4 200G interfaces. PAM4 400G modules MUST be used with the PAM4 400G interfaces. PAM4 400G modules may appear to operate correctly at 200G, but outliers (spikes in time error) may be seen, which will invalidate any results. Modules that don’t support 200G will show a warning indicating "not rate conformant" in the neo GUI. |
...
To achieve optimal timing performance when testing using PAM4 optical interfaces, the specific optical modules as listed below MUST be used:
400G PAM4 | |||||
Interface | Reach | Manufacturer | Part Number(s) | Software Release When First Supported | Comment |
---|---|---|---|---|---|
QSFP-DD | LR8 |
10km | Coherent (Finisar) | FTCD1323E1PCL | R7 | Use at 400G rate only. |
QSFP-DD | FR8 |
2km | Coherent (Finisar) | FTCD1333E1PCL | R7 | Use at 400G rate only. |
QSFP-DD | SR8 |
100m | Coherent (Finisar) | FTCD8613E1PCM | R7 | Use at 400G rate only. |
QSFP-DD | FR4 |
II-VI
2km | Coherent (Finisar) | FTCD4313E1PCL | R7 for FTCD4313E1PCL | Use at 400G rate only. FTCD4313E1PCL works for all scenarios. FTCD4313E2PCL works for all standard conformance tests, however some manually configured SyncE single sine frequency/amplitude combinations can cause link-loss. | |
QSFP-DD | LR4 10km | Coherent (Finisar) | FTCD4323E2PCL | R11 | Use at 400G rate only. |
200G PAM4 | |||||
Interface | Reach | Manufacturer | Part Number(s) | Software Release When First Supported | Comment |
---|---|---|---|---|---|
QSFP56 | SR4 |
II-VI
FTCC8612E1PCM
Coherent (Finisar) | FTCC8612E1PCM | R9 for FTCC8612E1PCM | FTCC8612E2PCM will be supported in a future release. |
QSFP56 | FR4 |
Coherent (Finisar) | FTCC1112E2PCL | R9 | |||
100G PAM4 | |||||
Interface | Reach | Manufacturer | Part Number(s) | Software Release When First Supported | Comment |
---|---|---|---|---|---|
SFP-DD | DR | Flexoptix | P.13S1HG.05.CAL | R11 | Calnex specific transceiver. Please contact Flexoptix for quotation: order@flexoptix.net. |
SFP-DD | FR | Flexoptix | P.13S1HG.2.CAL | R11 | Calnex specific transceiver. Please contact Flexoptix for quotation: order@flexoptix.net. |
SFP-DD | LR | Flexoptix | P.13S1HG.10.CAL | R11 | Calnex specific transceiver. Please contact Flexoptix for quotation: order@flexoptix.net. |
Note1: | Flexoptix transceiver part numbers are Calnex specific, denoted by the letters “CAL” in the part number. Flexoptix may add an extra “-MSA01” suffix to the part number for quotation and ordering purposes (eg P.13S1HG.10.CAL-MSA01). You must contact Flexoptix direct (order@flexoptix.net) because they do not list the Calnex specific parts on their website. | ||||
100G NRZ-PAM4 Conversion Transceivers | |||||
QSFP28 | DR | Innolight | TR-ZC13H-N00 | Neo PAM4 instruments:
Neo NRZ instruments:
| 100G PAM4 optical interface, instrument side is QSFP28 NRZ. Module supports generation and measurement accuracy of ±15ns. See Notes 2 and 3 below. |
QSFP28 |
FR1 | Innolight | TR-ZC13T-N00 | Neo PAM4 instruments:
Neo NRZ instruments:
| 100G PAM4 optical interface, instrument side is QSFP28 NRZ. Module supports generation and measurement accuracy of ±15ns. See Notes 2 and 3 below. | |
QSFP28 | LR | Innolight | TR-ZC13L-N00 | Neo PAM4 instruments:
Neo NRZ instruments:
| 100G PAM4 optical interface, instrument side is QSFP28 NRZ. Module supports generation and measurement accuracy of ±15ns. See Notes 2 and 3 below. |
Note 2: | Calnex recommend using Flexoptix 100G PAM4 transceivers instead of Innolight 100G NRZ-PAM4 conversion transceivers whenever possible for the best generation and measurement accuracy. | ||||
Note 3: | Innolight use the same part numbers for TR-ZC13H-N00, TR-ZC13T-N00 and TR-ZC13L-N00 transceivers manufactured in China and Thailand although they exhibit different transmit and receive latencies. Please check that the software loaded on your Paragon-neo supports the transceivers that you are using. | ||||
50G PAM4 | |||||
Interface | Reach | Manufacturer | Part Number(s) | Software Release When First Supported | Comment |
---|---|---|---|---|---|
SFP56 | LR | Gigalight |
GSS- |
SPO500-LRCZ | R9 | ||||
SFP56 | ER | Gigalight | GSS-SPO500-ER | R10 | |
SFP56 | SR |
II-VI
Gigalight | GSS-MPO560-SRC | R11 | |||
SFP56 | SR | Coherent (Finisar) | FTLF8556E1BCL | R7 |
SyncE Jitter
The modules listed below are those that MUST be used for SyncE jitter testing. These modules have been tested by Calnex to ensure that clock recovery can be bypassed and that they have sufficient bandwidth to allow the jitter performance of the device to be tested accurately. These modules are also known to operate correctly for PTP and SyncE Wander.
100G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
---|---|---|---|---|
QSFP28 | LR4 | Coherent (Finisar) | FTLC1151RDPL | No longer available from vendor. |
QSFP28 | LR4 | Coherent (Finisar) | FTLC1154RDPL | FTLC1156RDPL first supported by Paragon-neo R11 release. |
QSFP28 | SR4 | Coherent (Finisar) | FTLC9551REPM | FTLC9558REPM first supported by Paragon-neo R11 release. |
CXP | SR10 | Any Reputable Vendor | ||
40G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
QSFP+ | LR4 | Coherent (Finisar) | FTL4C1QE2C | FTL4C1QE3C first supported by Paragon-neo R11 release. |
25G and 10G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
SFP28 & SFP+ | LR | Coherent (Finisar) | FTLF1436W4BTV | |
SFP28 & SFP+ | LR | Coherent (Finisar) | FTLF1436P3BCL | FTLF1436P4BCL first supported by Paragon-neo R11 release. |
SFP28 & SFP+ | SR | Coherent (Finisar) | FTLF8536W4BTV | |
SFP28 & SFP+ | SR | Coherent (Finisar) | FTLF8536P4BCL | FTLF8536P5BCL first supported by Paragon-neo R11 release. |
SFP28 & SFP+ | SR | Coherent (Finisar) | FTLF8538P4BCL | FTLF8538P5BCL first supported by Paragon-neo R11 release. |
1G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
SFP | Short (SX) | Coherent (Finisar) | FTLF8519P3BNL |
SyncE Wander and PTP
For PTP and SyncE Wander on non-PAM4 interfaces, the following modules are known to operate correctly (in addition to those above).
100G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
CFP2 | LR4 | Coherent (Finisar) | FTLC1141RDNL | Rev 1 Paragon-100G only |
CFP2 | LR4 | Oclaro | TRB5E21FNF-LF002 | Rev 1 Paragon-100G only |
CFP2 | LR4 | Lumentum (JDSU) | JC2-10LM4AA1 | Rev 1 Paragon-100G only |
CFP2 | LR4 | Coherent (Finisar) | FTLC1121RDNL | Paragon-100G only |
QSFP28 | LR4 | Coherent (Finisar) | FTLC1151RDPL |
No longer available from vendor. | |||
QSFP28 | LR4 | Coherent (Finisar) | FTLC1154RDPL |
| FTLC1156RDPL first supported by Paragon-neo R11 release. | |||
25G and 10G | ||||
Interface | Reach | Manufacturer | Part Number(s) | Comment |
SFP28 & SFP+ | SR | Coherent (Finisar) | FTLF8536P4BCV | FTLF8536P5BCV first supported by Paragon-neo R11 release. |
For SyncE wander and PTP at 1G and 10G we expect all correctly configured modules to operate correctly. At other line rates we expect most correctly configured modules to operate correctly.
...
Hirose, LTD1302-BH: Module does not support multi-byte read. Supported by Paragon-neo version 01.00 and later
FS, SFP28-25GSR-85: Some of these modules are configured in a way that Paragon-neo does not recognise; others appear to be OK
Coherent (Finisar), FTLX1472M3BCL: These modules support a range of rates from 8.5Gb/s to 11.3Gb/s for Fibre Channel, SDH/SONET and 10GbE. When the CDR is disabled (which Paragon will do under certain circumstances), the module will set the CDR for 8.5Gb/s Fibre Channel and so no link will be able to be established.
Related articles
Filter by label (Content by label) | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
|