If you have a Spirent SNE and a valid service contract, the latest release is available through the Spirent Customer Service Centre (CSC). On the Downloads page, select the Impairment Product Line.
A CSC login is required to access the software download area. If you do not yet have a login, please register on the site.
If you have a Calnex SNE and a valid Calnex Support Service (CSS) contract, the latest release can be downloaded from Software Downloads on the Calnex website. Release notes are also available from the same location.
A CSS login is required to access the software download area. If you do not yet have a login, please register on the site.
Bandwidth Throttle now supports up to 20MB input buffer
In multi-user mode, port reservation can now be performed via the REST API
Updated Start / End Point statistics, added individual / global port statistics reset, added individual / global port link reset (via right-click)
MPEG H.264 impairment re-implemented. Added H.265 dynamic payload and H.265 support
Added new Markov Packet Drop mode
Accumulate and Burst impairment how supports delay time of up to 1 second
Start Point packet duplication did not work correctly in some scenarios with real world traffic
Fixed Packet Corruptor enable / disable via REST API
Bandwidth Throttle and Delay re-enabled disabled impairments on map stop via REST API
Jitter disabled on map stop via REST API
REST API did not always report enable / disable status correctly for some impairments
Jitter no longer holds on to a single packet on disable
A map created with the G.1050 wizard would cause the system to reboot
Traffic Replay with large packets could cause the system to reboot
Packet Drop impairment did not return correct settings via REST API until traffic passed through it
Port reservation did not handle non-contiguous licensed ports correctly
Maximum time for Accumulate and Burst was lower than expected when Jumbo mode enabled
RTP Statistics TAP performance improved
[SNE-548] Improved Bandwidth Throttle performance with TCP-based packet streams
[SNE-403] Fixed an issue restarting maps containing a packet capture TAP in overwrite mode
[SNE-406] PCAP files downloaded via RESTful Remote Control API did not contain a .pcap file extension
[SNE-453] Improved Packet Delay throughput for modes other than Constant
[SNE-455] Added enabling and disabling of Traffic Capture, Packet Corruption and Generic Modifier via the RESTful Remote Control API
[SNE-503] Fixed an issue that would prohibit large maps from starting successfully
[SNE-511] Fixed the Packet Reorder distance-based mode and improved throughput of this impairment
[SNE-478] Filters downstream of a VLAN filter on the “failed” path no longer increment their offsets by 4 bytes
[SNE-491] Fixed an issue with VLAN filters whereby traffic with non-zero PCP values would always fail
[SNE-569] VLAN IDs are now constrained to 0-4095
[SNE-492] Revised and updated the DiffServ filter DSCP list
[SNE-456] Fixed an issue with Jitter at high packet rates
[SNE-125] Fixed an issue that caused Jitter to reorder packets
[SNE-241] Fixed a memory leak
[SNE-533] Added admin SSH portal documentation
Fixed an issue that could cause a 10G port to advertise incorrect sync speeds
Updated supported Ethernet card firmware versions
Fixed an issue that could cause an upgrade to fail if the system clock was not set to the correct time
Fixed a Packet Drop issue in the time constraints functionality
Fixed an issue that could cause the Virtual Router to stop processing packets
Added additional debug information to the support logs
RESTful Remote Control API
Link Flapping (via API)
Jumbo Frame Mode, supporting Ethernet frames up to 9216 bytes
Ability to download logs for support
Increased the Standard Frame Mode Ethernet frame size, supporting up to 1536 bytes
Enhanced Idle Traffic Flow behavior
Added VLAN tag support in Ethernet Fragmentation impairment
Enhanced performance of all drop based impairments (Bandwidth Throttle, Packet Drop, Sink Hole, etc)
Improved accuracy of all time based impairments (e.g. Delay, Jitter, Bandwidth Throttle, etc)
Improved performance and accuracy of the background traffic generators
Many more functionality and stability improvements
SSH administration
Fix for graphs directly after a filter
New port icons
Many more GUI tweaks and improvements
[SNE-128] No data is being displayed if you insert a Bandwidth Stats Graph after a passed or failed link on a filter
[SNE-137] SNE Rel 5 Client Shows Wrong Traffic Path After Disabling Filter
[SNE-141] SNE Object Deletion Message Spelling
[SNE-144] SNE Captured Traffic Screen Incorrect
[SNE-145] SNE Traffic Capture Tap Invalid Options
[SNE-146] SNE GUI Shows Incorrect Traffic Flow When Filters are Disabled
[SNE-154] Stats Graphs Incorrect When Placed Directly After Filter
[SNE-170] When in Multi User mode, ports do not forward traffic on when not in use by on map
[SNE-171] Spirent GUI is calculating the Background Traffic Generator in 1024 instead of 1000
[SNE-172] Re-boot caused by repeated connection attempts
[SNE-174] SNE Reboots When 3 GB or Larger Traffic Capture Is Used
[SNE-181] Changes made to the Local Time from the Internal Clock do not persist on reboot
[SNE-246] Bandwidth Generator behaviour and performance